Let the efficiency of labeling machines fly

  　In order to ensure the stability and efficiency of the operation of the labeling machine, we in the daily use of the process, in addition to the operation process more effort, as users, to understand and master some of the equipment necessary maintenance means is also very important, the same labeling machine, others labeling high efficiency, long service life, and their own labeling machine efficiency is low, life is also broken, the reason for this, not only the method of operation, more importantly, maintenance and repair. More importantly, there is also maintenance and maintenance, the next small to introduce you to the labeling machine parts of the maintenance and adjustment methods, I hope that the following introduction can help you use the labeling machine.

　　1, the label box adjustment: the center line of the label box, the center axis of the label station and label paper tangent, the center axis of the label plate three points into a line, adjust to the label plate and label paper tangent (0 distance), and then the label box can be moved closer to 1mm ~ 2mm. Label paper in the label box and the gap between the two sides of the pressure bar should be between 0.8mm-1mm, the gap is too large to cause the displacement of the label paper in the label box, the appearance of oblique label; gap is too small will cause the push label is not smooth. The adjustment of the position of the marker box grasping hook: up and down, left and right grasping hook in the same vertical plane and evenly graze the marker paper, then you can smoothly grasp the marker. Label supply roller adjustment: when there is no label, the label pressure plate can be pressed to the front of the label box and equipped with a label, the label hook finger near the label can not be crushed.

　　2, the pressure brush device adjustment: the center of the label brush is right on the label and symmetrical on both sides, and perpendicular to the container surface. Pressure brush across the container overlap gap for: a single pressure brush for 10mm ~ 15mm, combined pressure brush for 5mm ~ 10mm. cleaning brush from the position of the sponge for 1mm ~ 2mm. pressure bottle head in the absence of bottles should be 20mm lower than when there is a bottle.

　　3、Adjustment of marking station: adjustment of scraping plate and rubber roller: scraping plate and rubber roller should not have a gap in the whole length, if there is a gap you can adjust the scraping plate by adjusting the eccentric bolt. Adjustment of rubber roller and marker plate: The marker plate and rubber roller are only in contact with each other without any pressure. If the gap is too big, the glue on the standard plate will be too much and cause throwing glue; if the gap is too small, the contact is too tight and the glue will be squeezed out and there is no glue on the half of the standard plate. Practice has proved that the gap between the label plate and the rubber roller is best between 0.1mm and 0.2mm, which can be achieved by adjusting the bearing seat of the lower part of the rubber roller and adjusting the bearing of the upper part of the rubber roller when necessary.

　　4、Adjustment of bottle inlet star wheel, bottle outlet star wheel and bottle inlet spiral rod: When adjusting bottle inlet and outlet star wheel and bottle inlet spiral rod, the pressed bottle head of the standard machine shall prevail. Adjustment of incoming star wheel: When the press head just overwhelms the bottle, adjust the incoming star wheel so that the bottle is located in the middle of the star wheel groove. Adjustment of screw rod into the bottle: When the bottle is located in the middle of the groove of the star wheel, adjust the screw rod so that the side of the screw rod into the bottle is close to the bottle but does not produce displacement. Adjustment of the star wheel of the bottle: when the bottle press head is just lifted, adjust the star wheel so that the bottle is located in the middle of the groove of the star wheel.

　　In addition, in terms of maintenance, we also need to focus on the following points.

　　1, labeling machine temporarily idle when not in use, should be unplugged and covered with a dust cloth, so as not to fall on the labeling machine dust. In addition, the labeling machine high temperature belt also needs to be cleaned and decontaminated regularly, so as to make the labeling machine better operation.

　　2, labeling machine in a period of time should be coated with lubricant. Because many parts of the labeling machine, such as gears, bearings and gearboxes, etc. after use, easy to rust and wear. And coated with lubricant, the parts are more smooth.

　　3, labeling machine working environment to maintain ventilation and dry, the best operating environment room temperature of twenty-five degrees Celsius.

　　4, if you want to keep the labeling machine for a long time, you need to check the operation of its cooling fan to ensure that the temperature is not too high, so as not to burn the electrical system.

　　5, in the process of daily use, the need for regular cleaning and maintenance of the labeling machine, because the equipment is easier to cause the deposition of dust, so every once in a while to clean up.

　　6, in order to ensure the smooth operation and normal use of the labeling machine, the need for regular cleaning of high-temperature components, especially the coding machine part.

　　And countless mechanical equipment, the use of labeling machine is also inseparable from the correct daily use as well as maintenance, only the two at the same time, in order to ensure that the labeling machine to play the strongest performance.