Sticker labeling machine common problems and repair methods

　　The use of self-adhesive labeling machine common problems and overhaul methods.

　　I. Labeling position is not stable

　　1, the pressure belt device may not be pressed, resulting in loose label belt, the electric eye detection is not allowed. Tighten the label to solve.

　　2, may be traction mechanism slippage or is not pressed, resulting in the smooth take away the backing paper. Tighten the traction mechanism to solve, too tight will pull the label distorted, in order to be able to pull the normal backing paper is better. (Usually if the pull out of the backing paper when wrinkled, then it should be when the pressure is too tight)

　　3, the shape of the object to be attached is not the same or positioning is not one to one. Control the quality of the product.

　　4, the object to be affixed should be placed parallel to the direction of the label out of the label (note whether the product in the labeling process is out of position, the left support rod can be properly raised than the right)

　　5, the object to be labeled in the labeling station should ensure smooth rotation (note that it can not touch the peeling plate), the object is too light, should be put down the labeling rod, press the object to be labeled.

　　6, in the double label state, out of a single label (1) out of a single label, the workpiece has been rotating, because there is no set the second label delay, the machine is waiting for the second label labeling signal state. (2) The workpiece stops after a single label is issued. It is because there is a signal interference in the electric eye (reset the electric eye) or the delay control is abnormal (click two clicks to move 2, then click two clicks to move 1 can be)

　　II. Mark with deviation

　　1, the pressure belt device is too tight, resulting in the standard with the bias, pressure belt strength can be reduced.

　　2. The tape is not corrected before the automatic operation, and the correction can be done again.

　　Three. Labeling quality is not good, there are bubbles or wrinkles

　　1, the labeling is not complete, can reduce the speed of labeling.

　　2, may be transparent labels, or labels are too soft.

　　3, the labeling gravity is not properly adjusted, important to adjust the labeling strength.

　　4, in the labeling of the beginning of the position of the crease, may be too soft label, the label has been bent when stretched out, raise the peeling plate position as close to the product.

　　5, the front and back of the label is not aligned, adjust the tilt of the support bar so that the product can be perpendicular to the direction of the label out. Through 1, 3 two screws to adjust the tilt of the support rod 2 to correct the label head and tail intersection error

　　6. move the product in the process of labeling in the other direction, slightly raise the support rod left support seat. Sticker labeling machine

　　IV. Equipment does not respond

　　1、Confirm that there is no problem with the power cord.

　　2, to confirm that the fuse next to the transmission socket is intact, if it has been burned, please replace it.

　　3, may be loose wiring inside the electrical box, please ask professionals to repair

　　V. Label backing paper often broken

　　1、The pressure belt device is too tight, causing the label to take away the deviation, pressure belt strength can be reduced.

　　2, the label backing paper quality is poor, or in the cut marks are too deep. This situation requires replacement of qualified labels.

　　3、Feeding speed is too fast, reduce the speed can be.

　　4, pay attention to observe whether the label is scratched in the process of walking

　　Six. Continuous labeling, stop labeling out of control

　　1, most of the detection of the electric eye is not set up, reset the electric eye can be solved.

　　2, the electric eye is not applicable to the detection of tags, the need to replace the applicable electric eye.

　　3, the electric eye is damaged, need to replace the electric eye.

　　4、Multiple steps on the foot switch to complete a labeling, the reason is the induction label electric eye signal interference, reset the electric eye can be

　　5, to confirm the label from the electric eye induction slot inside through the self-adhesive labeling machine

　　All labeling machines and filling production lines _ can be customized according to customer demand for non-standard labeling machines and production lines!